Tel: +86-0311-89642206 | Email: sales@metalspiping.com

Technical

Home / Technical

*YS1(yield strength of):ASTM B462 Alloy 20 forgings, annealed; ASTM B463 UNS N08020 plate, annealed; ASTM B473 UNS N08020 bar, annealed; ASTM B729 Alloy 20 smls. pipe & tube, annealed; ASTM B464 UNS N08020 wld. pipe, annealed; ASTM B468 UNS N08020 …

*TS1(tensile strength of): ASTM B462 UNS N08020 forgings, annealed; ASTM B463 Alloy 20 plate, annealed; ASTM B473 Alloy 20 bar, annealed; ASTM B729 Alloy 20 seamless pipe & tube, annealed; ASTM B464 UNS N08020 welded pipe, annealed; ASTM B468 UNS …

The table below provides maximum allowable stress values at given temperatures for various Alloy 20 materials. All tabulated values are in accordance with ASME BPVC Section II Part D. *Temp.: metal temperature, not exceeding. *MAS1, MAS2, MAS3, MAS4: maximum allowable …

Alloy 20 is endorsed by relative ASME Boiler & Pressure Vessel Codes (BPVC). A variety of product forms and conditions of Alloy 20 (UNS N08020) are listed in below table which are applicable for corresponding ASME BPVC specifications and temperature …

Alloy 20, UNS N08020, is also known as 20Cb-3, CN7M(castings), or DIN 2.4660. It has exceptional corrosion resistance to sulfuric acid and has good performance in handling pitting corrosion, crevice corrosion, intergranular corrosion, and stress-cracking corrosion. Meanwhile, its cost is comparatively …

General Introduction The Alloy 20 bars(UNS N08020) manufactured to ASTM B473 can be furnished in several types: (1)hot-finished rounds, square, octagons, and hexagons: 0.25″(6.35 mm) and over in diameter or size; (2)hot-finished flats: 0.25″~10″, inclusive, in width, 0.125″(3.175 mm) and …

Alloy 20 Pipe & Tube – Relative Standards *All pipes or tubes shall be furnished in stabilize-annealed condition. Chemical & Mechanical Requirements of Alloy 20 Pipe & Tubes The chemical & mechanical requirements of Alloy 20 (UNS N08020) is the …

ASTM B463 Alloy 20 plates, sheets, strips are widely used in the fabrication of pressure vessels, welded pipes or tubes, and other piping components. They can be furnished in various forms which are defined in below table. *The UNS designation …

Metals-Piping has committed experience of manufacturing a variety of ASTM B366 Alloy 20 fittings including 90° & 45° elbows, tees, reducers, 180° bends, caps, crosses, lap-joint stub ends, plugs, bushings, street elbows, , etc. These fittings has the UNS designation of …

General Introduction to Alloy 20 (UNS N08020) Alloy 20, designated as UNS N08020, is an austenitic corrosion-resistant alloy with nominal composition of 35Ni-35Fe-20Cr-Cb. It has the addition of small amount of copper and molybdenum. Alloy 20 was originally developed in 1951 …

ERNiCu-7 is a commonly used filler metal in the welding of Monel 400 piping materials. It is designated as UNS N04060, also known as Monel 60 with nominal composition of 65Ni-30Cu-3Mn-2Ti. The ERNiCu-7 bare welding electrode/ rod can be used in …

Monel 400 flanges manufactured to ASME B16.5 are usually made from two forms of raw material: ASTM B564 UNS N04400 forgings or ASTM B127 UNS N04400 plates. According to the standard, the pressure-temperature ratings can be furnished in two unit …

Page 20 of 26« First...10...1819202122...Last »
  • Product Categories

  • Contact Us

    Hebei Metals Industrial Limited
    (Shijiazhuang Metalsin Pipeline Tech Co., Ltd)
    No. 176, Zhonghua South Street, Shijiazhuang, China.
    Tel: +86-311-89642206
    Fax:+86-311-67906676
    Web: www.metalspiping.com
    Email: sales@metalspiping.com